VEHICLE SERVICE EQUIPMENT

Air Conditioning Service Equipment

Air Conditioning Service Equipment

RTI RHS780 Digital Air Conditioning

Refrigerant Handling System


Air Conditioning Service Equipment

Features
  • Recover, recycle, and recharge service times average less than 10 minutes. The quickest in the industry!
  • Patented recovery/recycling process - Heavy-duty compressor with true single-pass technology system for maximum throughput.
  • Digital heated power charge - Programmable with internal heating element. Air Conditioning service equipment Refills most vehicles in less than 30 seconds.
  • Advanced microprocessor - Air Conditioning service equipment Allows you to program charge amount, vacuum time, leak test, etc. and walk away.
  • Pressure detection device - AC service equipment Automatically restarts compressor if residual refrigerant is detected.
  • Internal weight scale - Industrial-strength scale with shock absorber eliminates inaccuracies and frequent calibration issues.
  • Refrigerant inventory - Accurate, continuous tracking of recovered, recharged, and available refrigerant. Long term memory for cumulative refrigerant management.
  • Solenoid-controlled gauge manifold - No leaky panel valves to open and close. Solenoids automatically open high and/or low side, eliminating potential mistakes.
  • Pressure protection - Suction pressure regulator protects compressor and other critical components.

Air Conditioning Service Equipment

Specifications
  • Electrical: 120VAC 60Hz. (230V available)
  • Dimensions: 43"H x 24.5"W x 29"D
  • Weight: 255 lbs.
  • Operating Range: 32° to 122°F
  • Scale Accuracy: ±0.03% load cell accuracy over useable range
  • Hoses: 11 ft.
  • Compressor: 1/3 HP, pressure protected, balanced startup
  • Condenser: 2270 sq. in. - fin surface area 0.38" diameter copper tubing
  • Condenser Fan: 5 blade, 8" diameter, 1550 RPM
  • Vacuum Pump: 7 CFM, 29.9 In. Hg.
  • Charging Cylinder: 30 lbs. DOT
  • Cylinder Heater: Heat Belt, 200 Watt
  • Process Time: Less than 10 min. average, recover/recycle/recharge
  • Warranty 5 years parts, 2 years labor

Air Conditioning Service Equipment

RTI RHS730 Digital Air Conditioning

Refrigerant Handling System


Air Conditioning Service Equipment

Features
  • Automation: Fully automatic service with pressure detection device Air Conditioning service equipment automatically restarts compressor if residual refrigerant is detected. Microprocessor control allows the technician to program vacuum time, leak test, charge amount, etc.
  • Accuracy: Internal industrial-strength weight scale with shock absorber Air Conditioning service equipment eliminates inaccuracies and frequent calibration issues. Refrigerant inventory continuously tracks recovered, recharged, and available refrigerant for productive refrigerant management.
  • Speed: Recovery/recycling process with heavy-duty compressor Air Conditioning service equipment allows maximum throughput and service times of less than 12 minutes average. Large fan-cooled condenser allows speedy recovery in high temperatures when Air Conditioning service is in demand.
  • Reliability: Highest quality compressor, solenoids, circuit board, switches, wiring, filters, weight scale, etc. Pressure regulator protects compressor and other critical components.
  • Intuition: Digital readout using plain language information and technician prompts makes this service so easy that any technician can be an Air Conditioning expert. Solenoids Air Conditioning service equipment automatically open high and/or low side, eliminating potential mistakes.

Air Conditioning Service Equipment

Specifications
  • Refrigerants: 2 models available: R134a or R12
  • Electrical: 120VAC 60Hz. (230V available)
  • Dimensions: 49"H x 20"W x 20"D
  • Weight: 244 lbs.
  • Operating Range: 32° to 122°F
  • Scale Accuracy: ±0.03% load cell accuracy over useable range
  • Hoses: 11 ft.
  • Compressor: 3/8 HP, pressure protected; oiled, hermetic
  • Condenser: 2270 sq. in. - fin surface area 0.38" diameter copper tubing
  • Condenser Fan: 5 blade, 8" diameter, 1550 RPM
  • Vacuum Pump: 7 CFM, 29.9 In. Hg.
  • Charging Cylinder: 30 lbs. DOT
  • Cylinder Heater: Heat Belt, 200 Watt, thermostatically controlled
  • Process Time: Less than 12 min. average, recover/recycle/recharge
  • Warranty 2 years parts and labor

Air Conditioning Service Equipment

RTI RHS2780 Dual Digital Air Conditioning

Refrigerant Handling System


Air Conditioning Service Equipment

Features
  • Patented recovery/recycling process: Process heavy-duty compressors with true single-pass technology system for maximum throughput.
  • Large Industrial Grade Fan-Cooled Condensers: Speed recovery, especially when temperatures are high ad Air Conditioning service is in demand.
  • Rapid deep vacuum: 7 CFM vacuum pump.
  • Integrated high or low side graduated oil charge: Fast, easy method for oil charge.
  • Internal weight scales: Industrial-strength scales eliminate inaccuracies and frequent calibration issues.
  • Rigidly mounted components: Robust weight scales provide accurate measurement of refrigerant recovered from and charged to vehicle.
  • Refrigerant Inventory: Accurate, continuous tracking of recovered, recharged, and available refrigerant. Long-term memory for cumulative refrigerant management.
  • Automatic prompts guide the technician.
  • Advanced microprocessor: Air Conditioning service equipment Allows you to program vacuum time, leak test, charge amount, etc., and walk away.
  • Pressure detection devices: Air Conditioning service equipment Automatically restarts compressors if residual refrigerant is detected.
  • Single-pass rapid air purge: Air Conditioning service equipment Quickly eliminates non-condensable gases.
  • Easy switchover: Instantaneous change between R134a and R12.
  • Pressure protection: Suction pressure regulators protect compressors and other critical components.

Air Conditioning Service Equipment

Specifications
  • Electrical: 120VAC 60Hz. (230V available)
  • Dimensions: 47"H x 31"W x 32"D
  • Weight: 340 lbs.
  • Operating Range: 32° to 122°F
  • Scale Accuracy: ±0.03% load cell accuracy over useable range
  • Hoses: 11 ft.
  • Compressor: 3/8 HP, pressure protected, balanced startup, oil bath hermetic
  • Condenser: 2270 sq. in. - fin surface area 0.38" diameter copper tubing
  • Condenser Fan: 5 blade, 8" diameter, 1550 RPM
  • Vacuum Pump: 7 CFM, 29.9 In. Hg.
  • Charging Cylinder: 30 lbs. DOT
  • Cylinder Heater: Heat Belt, 200 Watt, thermostatically controlled
  • Process Time: Less than 10 min. average, recover/recycle/recharge
  • Warranty 5 years parts, 2 years labor

Air Conditioning Service Equipment

RTI TC2670 Air Conditioning Dual Refrigerant

Management Center


Air Conditioning Service Equipment

Features
  • Air Conditioning Service Equipment Dual refrigerant model with no changeover time.
  • Long 11' hoses. Hook up to two cars. Service one while diagnosing another.
  • Automatic recovery and recycling.
  • Fan-cooled condenser for maximum speed even at high temperatures.
  • 7 CFM vacuum pump.
  • Fast, accurate analog charging.
  • Charging cylinders are heated and provide air-free charge.
  • R12 side is convertible to R134a in the future with conversion kit.

Air Conditioning Service Equipment

Specifications
  • Electrical: 120VAC 60Hz. (230V available)
  • Dimensions: 43"H x 33"W x 28"D
  • Weight: 264 lbs.
  • Operating Range: 32° to 122°F
  • Scale: Analog style (visual charging)
  • Hoses: 11 ft.
  • Compressor: 3/8 HP, pressure protected, balanced startup, oiled
  • Condenser: 2270 sq. in. - fin surface area 0.38" diameter copper tubing
  • Condenser Fan: 5 blade, 8" diameter, 1550 RPM
  • Vacuum Pump: 7 CFM, 29.9 In. Hg.
  • Charging Cylinder: Steel 8 lb. capacity
  • Cylinder Heater: Imbedded cartridge type - 125 watt
  • Process Time: Less than 10 min. average, recover/recycle/recharge
  • Warranty 2 years parts and labor
Air Conditioning Service EquipmentRobinair 34800-2K
Dual Refrigerant Recovery/Recycling

Air Conditioning Service Equipment

Features
  • Use the same unit for both R-12 and R-134a and save space in your shop. You can switch from one refrigerant to the other at the touch of a button. The 34800-2K comes with two built-in manifolds, two tanks, two compressors, and two electronic scales, so there's no need to clear or switch tanks. It takes up less room than two individual units and automatic operation makes it easy for any technician to use.
  • Microprocessor with Scrolling Display: Controls all functions including evacuation time and recharge amount, plus signals when it's time to change the filter-drier, pump oil, etc.
  • Automatic Air Purge: Any air in the tanks is automatically purged as needed to prevent the problems caused by air in a vehicle's Air Conditioning system.
  • Electronic Scale: Automatically shuts off the unit when the programmed amount of refrigerant has been recharged; also provides tank overfill protection and monitors the amount of refrigerant recovered. Storage vessels are permanently mounted and never need re-certification.
  • Single Hook-up: All functions are done in one fast, continuous operation through the one hook-up to the vehicle.
  • Heavy Duty Compressor: Pulls refrigerant from both the high and low sides of the Air Conditioning system for fast recovery. Compressor return oil separator keeps the compressor lubricated for long life and proper operation.
  • 6 CFM Vacuum Pump: Powerful Cool-Tech vacuum pump has the power and capacity to pull down quickly and dehydrate thoroughly to prepare the system for a recharge.
  • Super-Fast Charging: A typical auto recharge takes a minute or less.
  • Oil Injection: Lets you add system oil in just seconds while the unit is in a vacuum.

Air Conditioning Service Equipment

Specifications
  • Voltage: 115V, 60 Hz
  • Refrigerant Tanks: Two 30 lb. DOT approved
  • Operating Range: 50° to 120°F
  • Recycling Filter-Drier: 43 cu. in. spin-on type
  • Scale Resolution: 1/100 lb.
  • Pump Free Air Displacement: 6 CFM
  • Dimensions: 46"H x 27"W x 32"D
  • Weight: Approximately 200 lbs.

Air Conditioning Service Equipment

Robinair 34700-2K
R-134a Recovery/Recycling

Air Conditioning Service Equipment

Features
  • The Cool-Tech 700 recovers, recycles, evacuates and recharges R-134a quickly and accurately. Built in the new "sidewinder" cabinet, it combines proven technology with the latest in time-saving features.
  • Automatic Refrigerant Refill: With this latest advance, you never have to stop in the middle of a job to change refrigerant tanks. The unit maintains 12 to 15 pounds of refrigerant in an internal vessel, and signals when it's time to change the supply tank so no monitoring is required.
  • Automatic Air Purge: Eliminates damaging air without any monitoring of gauges or opening of valves.
  • Automatic Oil Drain: The unit automatically drains system oil captured during recovery, and the display reminds you to empty the bottle. Calibrations on the container clearly show you how much oil needs to be replaced.
  • Electronic Scale: The scale is mounted internally for protection and has a dampening mechanism that protects against impact shocks such as movement over rough surfaces. The scale weighs recovered refrigerant and charges by weigh for greatest accuracy.
  • Internal Storage Vessel: Refrigerant is recovered into and charged out of this vessel, which is permanently mounted to the electronic scale for continuing reliability.
  • Internal Manifold: A Robinair exclusive, this block manifold contains all the solenoids that control refrigerant flow, reducing the possibility of leaking connections.
  • R12 side is convertible to R134a in the future with conversion kit.
  • Features that speed service:
    • 6 CFM vacuum pump for fast, thorough pull-down.
    • Heavy-duty compressor pulls from both high and low sides during recovery.
    • Single pass recycling meets SAE specs.
    • Oil injector lets you add system oil in seconds

Air Conditioning Service Equipment

Specifications

  • Voltage: 115V, 60 Hz
  • Refrigerant Container: On-board 30 lb. vessel (source tank not included)
  • Operating Range: 50° to 120°F
  • Recycling Filter-Drier: 43 cu. in. spin-on type
  • Pump Free Air Displacement: 6 cfm
  • Dimensions: 52"H x 33"W x 20"D
  • Weight: 180 lbs.

Air Conditioning Service Equipment

Robinair Cool-Tech 34700Z
Recovery, Recycling, Recharging

Air Conditioning Service Equipment

Features
  • The Cool-Tech 34700Z recovers, recycles, evacuates, leak tests, and recharges R-134a quickly and accurately.
  • Automatic Function: With this new option, you can program the unit to recover, vacuum, leak test, charge, and then walk away without having to operate panel valves.
  • Vacuum Leak Test: Will monitor the vacuum level after an evacuation, and inform the technician of a possible leak in the vehicle's Air Conditioning system.
  • Automatic Refrigerant Refill: With this latest advance, you never have to stop in the middle of a job to change refrigerant tanks. The unit maintains 12 to 15 pounds of refrigerant in an internal vessel, and signals when it's time to change the supply tank, so no monitoring is required.
  • Automatic Air Purge: Air Conditioning service equipment Eliminates damaging air without any monitoring of gauges or opening of valves.
  • Automatic Oil Drain: The unit automatically drains system oil captured during recovery, ad the display reminds you to empty the bottle. Graduations on the container clearly show you how much oil needs to be replaced.
  • Refrigerant Charging: Has never been this easy. Select a charge mode from either the high side, low side, or both.
  • Electronic Scale: The scale is mounted internally for protection and has a dampening mechanism that protects against impact shocks, such as movement over rough surfaces. The scale weighs recovered refrigerant and charges by weight for greatest accuracy.
  • Internal Storage Vessel: Refrigerant is recovered into and charged out of this vessel, which is permanently mounted to the electronic scale for continuing reliability.
  • Internal Manifold: A Robinair exclusive, this block manifold contains all the solenoids that control refrigerant flow in and out of the unit, reducing the possibility of leaking connections and eliminating the need to operate panel valves.
  • Ergonomic Design: The cabinet is easy to maneuver between service bays and position near the vehicle.
  • Large Gauges: The high and low side gauges are mounted at an angle that's easy to see, and they're a full 4" in diameter.
  • Features that speed service:
    • 6 CFM vacuum pump for fast, thorough pull-down.
    • Heavy-duty compressor pulls from both high and low sides during recovery.
    • Single pass recycling meets SAE specs.
    • Oil injector lets you add system oil in seconds

Air Conditioning Service Equipment

Specifications

  • Voltage: 115V, 60 Hz
  • Refrigerant Container: On-board 30 lb. vessel (source tank not included)
  • Operating Range: 50° to 120 °F
  • Recycling Filter-Drier: 43 cu. in. spin on type
  • Pump Free Air Displacement: 6 cfm
  • Dimensions: 50"H x 34"W x 23"D
  • Shipping Weight: 235 lbs.

Air Conditioning Service Equipment

Viper VR-9000 Air Conditioning

Service Center

Air Conditioning Service Equipment

Features
  • User's choice: Select either a specific service mode or fully automatic.
  • LCD display with six language options: Walks a technician through job set-up.
  • Accurate charging: To within 0.50 ounces.
  • Heavy duty 2-stage 7 cfm vacuum pump: Provides a quick, deep vacuum.
  • R-134a dedicated machine: For late model cars and trucks.
  • Spin-off filter: Effective high volume design.
  • Includes large capacity 50 lb. tank: For 134a refrigerant.
  • UL approved.
  • Complete with two year warranty.
  • Fast, easy to use air purge.

Air Conditioning Service Equipment

Specifications
  • Primary Input: 120 Volt, Single Phase, 60 Hz
  • Service Modes: R/R/E/C
  • Service Types: Automatic or Selected
  • Refrigerant Type: R-134a
  • Vacuum Pump: 7 CFM
  • Oil Separation: Manual
  • Oil Injection: Manual
  • Air Purge: Manual
  • Cylinder: 50 lb. R-134a
  • Weight: 207

Air Conditioning Service Equipment

Viper VR-8000

Air Conditioning Service Center

Air Conditioning Service Equipment

Features
  • Semi-automatic operation.
  • Multiple functions.
  • Single pass distillation.
  • Heavy-duty, 2-stage 5CFM vacuum pump.
  • Charging accuracy to within .5 oz.
  • Large 50 lb. R-134a cylinder.
  • Built-in oil injection.
  • UL-approved.
  • Optional onboard Viper Identifier (Model No. 800520) available.

Air Conditioning Service Equipment

Specifications
  • Primary Input: 120 Volt, Single Phase, 60 Hz
  • Service Modes: R/R/E/C
  • Service Types: Semi-Automatic
  • Refrigerant Type: R-134a
  • Vacuum Pump: 5 CFM
  • Oil Separation: Manual
  • Oil Injection: Manual
  • Air Purge: Manual
  • Cylinder: 50 lbs.
  • Approved: UL
  • Warranty: 2 Year
  • Weight: 187
Note: The features and specifications listed above are provided by the manufacturer(s) and may change without notice.
         Call Vehicle Service Equipment for Information.
About Us | Contact Us | Privacy | ©2005 Vehicle Service Equipment Corporation