VEHICLE SERVICE EQUIPMENT

Welders

Welders

Milweld Auto Arc
XLT 270 MIG Welder


Welders

Features
  • Welds 22 gauge up to 1/2" material in a single pass
  • Excellent aluminum welding with optional spool gun
  • Seven-tap voltage control allows for a smooth, easy-to-control arc
  • Infinite wire feed speed control for precise adjustment
  • Comes complete with 200 amp gun and built-in running gear/cylinder rack
  • Handles wire spools up to 45 lbs.
  • Built-in thermal overload protect the unit
  • Reversible drive rolls: two grooves for three wire sizes on one drive roll

Welders

Specifications
  • Power: 200 (208)/230 VAC, 60 Hz
  • Rated Output: 200 A, 24 VDC at 60% Duty Cycle
  • Wire Feed Speed: 90 - 750 IPM
  • Current Range: 30 - 250 A
  • Maximum Open Circuit Voltage: 36
  • Dimensions: 32-1/4"H x 108-7/8"W x 36-1/2"D
  • Weight: 235 lbs.

Welders

Comes Complete With
  • 12-1/2 ft., 200 amp MIG gun
  • Regulator dual gauge and gas hose
  • 10 ft. primary and work cables
  • 10 lb. spool of 0.35" solid wire
  • 0.23, 0.30/0.35" dual groove drive roll
  • Extra contact tips and set up chart
  • Runs 0.45 with optional drive roll

Welders

Milweld Auto Arc
Quick Cut 4500 Plasma Cutter


Welders

Features
  • Dual input voltage located in back of unit allows either 115 or 230 VAC input power and provides patented protection in case of incorrect switch position.
  • Starts without high-frequency so it will not interfere with controls or computers.
  • Pilot arc controller increases cutting capabilities and speeds, and improves tip life.
  • Post flow cooling circuit extends the life of the consumables and torch by cooling them with post flow air after the trigger is released.
  • LVC line voltage compensation provides peak performance power under variable conditions (power fluctuations up to +/- 15%) for steady cuts and cleaner ending cuts.
  • Gas/air filter/regulator inside the power source provides added protection during transportation. Standard air connection on back panel for easy gas or air hookup.

Welders

Specifications
  • Process: Air Plasma Cutting
  • Rated Output: 27 A at 90 VDC, 35% Duty Cycle
  • 1/15" Standoff Cutting: Rated - 3/8" / Quality - 1/2" / Sever - 5/8"
  • Drag Cutting: Rated - 5/8" / Quality - 3/8" / Sever: 1/2"
  • Plasma Gas Flow/Pressure: 4.5 CFM at 60 PSI

Welders

Comes Complete With
  • ICE-27C hand-held torch with 20 ft. cable
  • 15 ft. heavy duty work cable with clamp
  • Extra consumables (3 electrodes, 3 tips and 1 air fitting)
  • 10 ft. power cord with 115 VAC, 20 A plug

Welders

Milweld Auto Arc
XLT 222 MIG Welder


Welders

Features
  • Welds 22 gauge up to 3/8" material in a single pass.
  • Excellent aluminum welding with optional Spool mate 3035 spool gun.
  • Six-tap voltage control allows for a smooth, easy-to-control arc.
  • Infinite wire feed speed control for precise adjustment of penetration and weld bead shape.
  • Comes complete with gun and built-in running gear/cylinder rack.
  • Handles wire spools up to 12"; wire feed speed adjusts from 90 to 750 IPM.
  • Built-in thermal overload protects the unit.
  • Reversible drive rolls: two grooves for three wire sizes on on drive roll. Decreases spare parts and changeover time.
  • Hinged door for easy access to wire drive system for spool and drive roll changes.

Welders

Specifications
  • Rated Output: 150 A, 23 V DC at 40% duty cycle
  • Current Range: 30 - 210 amps
  • Open Circuit Voltage: 33 V
  • Wire Feed Speed: 90 - 750 IPM
  • Dimensions: 31-1/4"H x 18-7/8"W x 36-1/2"D
  • Net Weight: 144 lb

Welders

Comes Complete With
  • Wire feeder
  • Running gear
  • Cylinder rack
  • Regulator/flow gauge
  • MIG gun
  • Cable and clamp
  • Extra tips

Welders

Milweld Auto Arc
Moonliter 150 TIG Welder


Welders

Features
  • Upgraded circuitry gives you finer TIG output adjustment with the fingertip control.
  • AC output for superior aluminum welding.
  • DC output for mild and stainless steel.
  • Four-position polarity and range selector.
  • Patented, built-in arc assist starter for DC TIG and assist stabilizer for AC TIG on aluminum.
  • Preset automatic post flow timer protects tungsten tip, work piece and torch.
  • Automatic high-temperature shut down.

Welders

Specifications
  • Rated Output: 150 A, 15 V DC at 20% duty cycle
  • TIG Welding Amperage Range: AC Low (20-50), AC High (50-165), DC (30-160)
  • Maximum Open Circuit Voltage: 78
  • Rated Input: 230 V 52A
  • Dimensions: 18"H x 13"W x 25-1/2"D
  • Net Weight: 140 lb

Welders

Comes Complete With
  • Power Source with primary cord and plug
  • 12 ft work cable and clamp
  • 15 ft Stick electrode holder
  • 20 ft finger tip control torch
  • Gas regulator, flow meter and hose
  • "How-to" videotape
Note: The features and specifications listed above are provided by the manufacturer(s) and may change without notice.
         Call Vehicle Service Equipment for Information.
About Us | Contact Us | Privacy | ©2005 Vehicle Service Equipment Corporation